rotaryThermo/main/drivers/display/display.c

#include "display.h"

#include <string.h>

#include "driver/ledc.h"
#include "esp_check.h"
#include "esp_lcd_panel_io.h"
#include "esp_lcd_panel_io_additions.h"
#include "esp_lcd_panel_rgb.h"
#include "esp_log.h"
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "pcf8574.h"
#include "st7701_init.h"

static const char *TAG = "display";

/* ---- Pinout: docs/HARDWARE.md, verified against Elecrow's own example ---- */

#define PIN_LCD_CS          16
#define PIN_LCD_SCK         2
#define PIN_LCD_SDA         1

#define PIN_LCD_DE          40
#define PIN_LCD_HSYNC       15
#define PIN_LCD_VSYNC       7
#define PIN_LCD_PCLK        41

#define PIN_BACKLIGHT       6

/*
 * SPI mode 0. Arduino_GFX's Arduino_SWSPI::begin() drives SCK low at init and
 * shifts on the rising edge. Elecrow's ESPHome config says MODE3, but that
 * file also documents its own colours as wrong.
 *
 * If the panel is black on first bring-up, this is the first thing to try
 * changing — before touching the init sequence, and long before rewriting
 * anything else.
 */
#define ST7701_SPI_MODE     0

/*
 * Timings from the vendor's Arduino example. The ESPHome example uses
 * 20/10/10 and 8/10/10 instead; either set should work. Swap if the image
 * rolls or shears.
 */
#define LCD_PCLK_HZ         (18 * 1000 * 1000)
#define LCD_HSYNC_FRONT     10
#define LCD_HSYNC_PULSE     4
#define LCD_HSYNC_BACK      20
#define LCD_VSYNC_FRONT     10
#define LCD_VSYNC_PULSE     4
#define LCD_VSYNC_BACK      20

#define BACKLIGHT_LEDC_TIMER    LEDC_TIMER_0
#define BACKLIGHT_LEDC_CHANNEL  LEDC_CHANNEL_0
#define BACKLIGHT_LEDC_MODE     LEDC_LOW_SPEED_MODE
#define BACKLIGHT_RES           LEDC_TIMER_10_BIT

static esp_lcd_panel_handle_t s_panel;
static void *s_fb0, *s_fb1;

/* ------------------------------------------------------------ backlight -- */

static esp_err_t backlight_init(void)
{
    ledc_timer_config_t timer = {
        .speed_mode = BACKLIGHT_LEDC_MODE,
        .timer_num = BACKLIGHT_LEDC_TIMER,
        .duty_resolution = BACKLIGHT_RES,
        .freq_hz = 5000,
        .clk_cfg = LEDC_AUTO_CLK,
    };
    ESP_RETURN_ON_ERROR(ledc_timer_config(&timer), TAG, "ledc timer");

    ledc_channel_config_t ch = {
        .gpio_num = PIN_BACKLIGHT,
        .speed_mode = BACKLIGHT_LEDC_MODE,
        .channel = BACKLIGHT_LEDC_CHANNEL,
        .timer_sel = BACKLIGHT_LEDC_TIMER,
        .duty = 0,
        .hpoint = 0,
    };
    return ledc_channel_config(&ch);
}

void display_set_backlight(uint8_t percent)
{
    if (percent > 100) {
        percent = 100;
    }
    uint32_t max = (1u << BACKLIGHT_RES) - 1;
    uint32_t duty = (max * percent) / 100;

    ledc_set_duty(BACKLIGHT_LEDC_MODE, BACKLIGHT_LEDC_CHANNEL, duty);
    ledc_update_duty(BACKLIGHT_LEDC_MODE, BACKLIGHT_LEDC_CHANNEL);
}

/* --------------------------------------------------------- reset dance --- */

/*
 * Reproduces the vendor example's setup() ordering exactly, including the P3
 * ("LCD power") pulse. Despite the label, P3 goes high before the reset and
 * low again once the backlight is running, which only makes sense as blanking
 * to hide init garbage. Copied rather than reasoned about — see
 * docs/HARDWARE.md.
 *
 * P1 is deliberately untouched throughout: it is the relay.
 */
static esp_err_t panel_power_and_reset(void)
{
    ESP_RETURN_ON_ERROR(pcf8574_write(PCF_PIN_LCD_POWER, true), TAG, "p3");
    vTaskDelay(pdMS_TO_TICKS(100));

    ESP_RETURN_ON_ERROR(pcf8574_write(PCF_PIN_LCD_RST, true), TAG, "p4 hi");
    vTaskDelay(pdMS_TO_TICKS(100));
    ESP_RETURN_ON_ERROR(pcf8574_write(PCF_PIN_LCD_RST, false), TAG, "p4 lo");
    vTaskDelay(pdMS_TO_TICKS(120));
    ESP_RETURN_ON_ERROR(pcf8574_write(PCF_PIN_LCD_RST, true), TAG, "p4 hi2");
    vTaskDelay(pdMS_TO_TICKS(120));

    return ESP_OK;
}

/* --------------------------------------------------------------- init ---- */

static esp_err_t send_init_sequence(void)
{
    esp_lcd_panel_io_handle_t io = NULL;

    esp_lcd_panel_io_3wire_spi_config_t io_cfg = {
        .line_config = {
            .cs_io_type = IO_TYPE_GPIO,
            .cs_gpio_num = PIN_LCD_CS,
            .scl_io_type = IO_TYPE_GPIO,
            .scl_gpio_num = PIN_LCD_SCK,
            .sda_io_type = IO_TYPE_GPIO,
            .sda_gpio_num = PIN_LCD_SDA,
            .io_expander = NULL,
        },
        .expect_clk_speed = PANEL_IO_3WIRE_SPI_CLK_MAX,
        .spi_mode = ST7701_SPI_MODE,
        .lcd_cmd_bytes = 1,
        .lcd_param_bytes = 1,
        .flags = {
            .use_dc_bit = 1,        /* 9-bit frames: DC bit then 8 data bits */
            .dc_zero_on_data = 0,   /* DC=0 command, DC=1 data (ST7701 order) */
            .lsb_first = 0,
            .cs_high_active = 0,
            /*
             * Keep CS inactive after we delete this IO. The RGB bus takes over
             * the panel from here and must not see CS wander.
             */
            .del_keep_cs_inactive = 1,
        },
    };

    ESP_RETURN_ON_ERROR(esp_lcd_new_panel_io_3wire_spi(&io_cfg, &io),
                        TAG, "3wire spi io");

    esp_err_t err = ESP_OK;
    for (size_t i = 0; i < ST7701_INIT_SEQ_LEN; i++) {
        const st7701_cmd_t *c = &st7701_init_seq[i];

        err = esp_lcd_panel_io_tx_param(io, c->cmd,
                                        c->data_len ? c->data : NULL,
                                        c->data_len);
        if (err != ESP_OK) {
            ESP_LOGE(TAG, "init cmd %u (0x%02X) failed: %s",
                     (unsigned)i, c->cmd, esp_err_to_name(err));
            break;
        }
        if (c->delay_ms) {
            vTaskDelay(pdMS_TO_TICKS(c->delay_ms));
        }
    }

    /* The init bus is single-use; the RGB peripheral owns the panel now. */
    esp_lcd_panel_io_del(io);

    if (err == ESP_OK) {
        ESP_LOGI(TAG, "ST7701S init sequence sent (%u commands)",
                 (unsigned)ST7701_INIT_SEQ_LEN);
    }
    return err;
}

static esp_err_t rgb_panel_init(void)
{
    esp_lcd_rgb_panel_config_t cfg = {
        .clk_src = LCD_CLK_SRC_PLL160M,
        .timings = {
            .pclk_hz = LCD_PCLK_HZ,
            .h_res = DISPLAY_H_RES,
            .v_res = DISPLAY_V_RES,
            .hsync_pulse_width = LCD_HSYNC_PULSE,
            .hsync_back_porch = LCD_HSYNC_BACK,
            .hsync_front_porch = LCD_HSYNC_FRONT,
            .vsync_pulse_width = LCD_VSYNC_PULSE,
            .vsync_back_porch = LCD_VSYNC_BACK,
            .vsync_front_porch = LCD_VSYNC_FRONT,
            .flags = {
                /* Elecrow's ESPHome config sets pclk_inverted, i.e. data is
                 * latched on the falling edge. */
                .pclk_active_neg = 1,
            },
        },
        .data_width = 16,
        .bits_per_pixel = 16,
        .num_fbs = 2,
        /*
         * No bounce buffers — this is what makes runtime NVS writes safe.
         * See the header comment. Do not "optimise" this to a non-zero value
         * without re-reading PRD 8.2.
         */
        .bounce_buffer_size_px = 0,
        .psram_trans_align = 64,
        .hsync_gpio_num = PIN_LCD_HSYNC,
        .vsync_gpio_num = PIN_LCD_VSYNC,
        .de_gpio_num = PIN_LCD_DE,
        .pclk_gpio_num = PIN_LCD_PCLK,
        .disp_gpio_num = -1,
        /*
         * RGB565 bit order: data[0..4] = blue, [5..10] = green, [11..15] = red.
         * If red and blue come out swapped, swap these two blocks — the panel's
         * own MADCTL is already 0x00 (RGB) from the init sequence.
         */
        .data_gpio_nums = {
            5, 45, 48, 47, 21,              /* B0..B4 */
            14, 13, 12, 11, 10, 9,          /* G0..G5 */
            46, 3, 8, 18, 17,               /* R0..R4 */
        },
        .flags = {
            .fb_in_psram = 1,
        },
    };

    ESP_RETURN_ON_ERROR(esp_lcd_new_rgb_panel(&cfg, &s_panel), TAG, "rgb panel");
    ESP_RETURN_ON_ERROR(esp_lcd_panel_reset(s_panel), TAG, "panel reset");
    ESP_RETURN_ON_ERROR(esp_lcd_panel_init(s_panel), TAG, "panel init");

    ESP_RETURN_ON_ERROR(
        esp_lcd_rgb_panel_get_frame_buffer(s_panel, 2, &s_fb0, &s_fb1),
        TAG, "get framebuffers");

    ESP_LOGI(TAG, "RGB panel up: %dx%d @ %d MHz, fb0=%p fb1=%p",
             DISPLAY_H_RES, DISPLAY_V_RES, LCD_PCLK_HZ / 1000000, s_fb0, s_fb1);
    return ESP_OK;
}

esp_err_t display_init(void)
{
    if (!pcf8574_is_ready()) {
        ESP_LOGE(TAG, "expander not ready — cannot sequence panel power");
        return ESP_ERR_INVALID_STATE;
    }

    ESP_RETURN_ON_ERROR(panel_power_and_reset(), TAG, "power/reset");
    ESP_RETURN_ON_ERROR(send_init_sequence(), TAG, "init sequence");
    ESP_RETURN_ON_ERROR(rgb_panel_init(), TAG, "rgb");
    ESP_RETURN_ON_ERROR(backlight_init(), TAG, "backlight");

    /* Clear both buffers before the backlight comes up, so the first thing on
     * screen is black rather than whatever was in PSRAM. */
    size_t fb_bytes = (size_t)DISPLAY_H_RES * DISPLAY_V_RES * 2;
    memset(s_fb0, 0, fb_bytes);
    memset(s_fb1, 0, fb_bytes);

    display_set_backlight(80);

    /* Vendor ordering: P3 low once the backlight is running. */
    pcf8574_write(PCF_PIN_LCD_POWER, false);

    return ESP_OK;
}

esp_lcd_panel_handle_t display_panel(void)
{
    return s_panel;
}

esp_err_t display_get_framebuffers(void **fb0, void **fb1)
{
    if (!s_panel) {
        return ESP_ERR_INVALID_STATE;
    }
    if (fb0) {
        *fb0 = s_fb0;
    }
    if (fb1) {
        *fb1 = s_fb1;
    }
    return ESP_OK;
}

void display_test_pattern(void)
{
    static const uint16_t bars[] = {
        0xF800, /* red    */
        0x07E0, /* green  */
        0x001F, /* blue   */
        0xFFFF, /* white  */
        0xFFE0, /* yellow */
        0x07FF, /* cyan   */
        0xF81F, /* magenta*/
        0x0000, /* black  */
    };
    const int n = sizeof(bars) / sizeof(bars[0]);
    const int bar_w = DISPLAY_H_RES / n;

    uint16_t *fb = (uint16_t *)s_fb0;
    if (!fb) {
        ESP_LOGE(TAG, "no framebuffer");
        return;
    }

    for (int y = 0; y < DISPLAY_V_RES; y++) {
        for (int x = 0; x < DISPLAY_H_RES; x++) {
            int i = x / bar_w;
            fb[y * DISPLAY_H_RES + x] = bars[i < n ? i : n - 1];
        }
    }

    esp_lcd_panel_draw_bitmap(s_panel, 0, 0, DISPLAY_H_RES, DISPLAY_V_RES, fb);
    ESP_LOGI(TAG, "colour bars drawn — this is the PRD phase-2 check");
}